What Fuel Does a Generac Generator Use? It Depends on What You're Powering

Every week someone calls our desk asking some version of "what fuel does a Generac generator use?" They want a single answer. There isn't one.

I coordinate emergency power deployments for a commercial electrical supply company. I've handled 200+ rush orders in six years, including same-day turnarounds for facility managers, event planners, and one very stressed wedding caterer. The fuel question is almost never just about fuel. It's about what you're powering, how long you need to run, and what your electrical infrastructure already looks like.

Here's how I sort the calls that come in with a deadline attached.

Three scenarios, three different answers

Nearly every incoming request falls into one of three buckets:

  • Scenario A: Backing up a house or small office — typically under 22kW
  • Scenario B: Protecting a commercial facility — 22–38kW, sometimes paralleled
  • Scenario C: Temporary or portable power for a job site or event

Get the bucket wrong and everything downstream — fuel type, tank sizing, electrical protection — is wrong too. I've seen a homeowner sold a 38kW commercial unit for a 1,800 sq ft ranch house. The install cost more than the generator.

Scenario A: Home standby (under 22kW)

If you're a homeowner or you manage a small office, the Generac 20kW propane generator is probably the unit you've been quoted. It's the workhorse of residential standby — air-cooled, relatively compact, and sized for a typical 2,000–2,500 sq ft house with central air.

Fuel

What fuel does a Generac generator use in this class? Either natural gas or liquid propane. But the choice matters more than the brochure suggests.

Natural gas is cheaper per BTU and never runs out (assuming the grid holds). Propane delivers more energy per cubic foot and doesn't depend on utility infrastructure — which is the whole point of a standby system, in my opinion. I've seen too many "natural gas backup" installs go dark when the local utility lost pressure during a regional event.

To be fair, most suburban installs go NG because nobody wants a 500-gallon tank in the side yard. That's a legitimate trade-off. Just go in knowing what you're trading.

Electrical protection

This is where people cut corners. A Type 2 surge protector at the transfer switch or main panel is the minimum I'd recommend. Type 2 handles the residual surge that gets past the utility meter. If your utility has a history of flickers or you're on the end of a long feeder line, consider a Type 1 at the service entrance as a first line of defense. The cost difference is usually $150–$300 as of early 2025 pricing. That's cheap insurance compared to replacing a control board.

Maintenance reality

The 12V starting battery needs a maintainer, not a trickle charger from the auto parts store. And no, your eneloop battery charger for AA cells is not going to help here — wrong chemistry, wrong float voltage. Use a proper battery tender rated for AGM or lead-acid standby batteries. I've replaced three batteries this year because someone left a cheap charger on them and boiled the electrolyte dry.

Scenario B: Commercial facility (22–38kW)

This is where the fuel conversation gets more interesting — and where the 20kW unit is underpowered. A 22–38kW commercial standby is typically liquid-cooled, runs at 1800 RPM, and is designed for multi-day continuous operation.

Fuel

What fuel does a Generac generator use at this scale? Natural gas is the commercial default because you're usually on a medium-pressure service and the fuel cost per kWh is lower. But if your facility is rural or your gas utility has capacity constraints, propane with a 1,000+ gallon tank is more reliable. I've seen hospitals and data closets specify diesel — that's a different beast, and I'll get to it.

Surge protection

Here the Type 1 vs Type 2 surge protector question actually matters. Type 1 devices install on the line side of the main disconnect — they handle outside surges without a separate overcurrent device. Type 2 goes on the load side, at a panelboard or transfer switch. For a commercial install with a Generac standby, I spec a Type 1 at the service entrance and a Type 2 at the generator distribution panel. Two layers. Look for UL 1449 4th edition rating on the data sheet — if it doesn't say that, put it back on the shelf.

In March 2024, a client called 36 hours before a fire marshal inspection needing a 20kW propane unit installed and permitted. We found a dealer with stock, paid $400 extra in freight (which, honestly, felt excessive for a two-day upgrade), and delivered with 6 hours to spare. Missing that deadline would have shut down their grand opening. The unit itself was fine. The permitting was the bottleneck.

The diesel tangent

If your facility already runs diesel equipment — say a fleet of 6.6 Duramax trucks — you might be tempted to spec a diesel standby generator for fuel commonality. I get why. But stationary diesel maintenance isn't the same as road vehicle maintenance. The fuel filter 6.6 Duramax owners replace on a mileage schedule isn't the same cadence a stationary unit needs. The truck's filter sees flow and heat; the generator's filter sees months of stagnant fuel. Stationary units need fuel polishing, water separation, and more frequent filter changes. I've seen a 30kW diesel unit fail a load test because nobody changed the filter in 18 months. The truck got serviced every 5,000 miles. The generator got nothing.

Scenario C: Portable and temporary power

This is the scenario where the fuel question has the most wrong answers floating around job sites.

Portable Generac units in the 6–12kW range run on gasoline or propane. Gasoline is more energy-dense and easier to find on short notice. Propane stores indefinitely and doesn't go stale. For a weekend event, gasoline is fine. For a construction site running six days a week for three months, propane is the better call — you're not sending someone to the gas station every morning.

Battery maintenance on portables is where I see the most avoidable failures. Crews pull the starting battery and put it on whatever charger is in the truck. A charger with a float mode is fine. But the eneloop battery charger sitting in your toolbox is designed for NiMH cells, not a 12V lead-acid starting battery. Wrong tool, predictable result.

Surge protection: portable generators don't have the same grounding and bonding as a permanent install. If you're backfeeding a panel (please don't, but if you are), a Type 2 surge protector on the load side is the least you can do. Type 1 doesn't apply — there's no service entrance to protect.

How to tell which scenario you're actually in

Three questions narrow it down:

  1. What's your largest motor load? A 5-ton AC compressor needs roughly 15–18kW just for startup. If you have two, you're in Scenario B territory even if the building is "just" a large house.
  2. How long do you need to run unattended? Under 8 hours, portable is fine. Over 24 hours, you need a permanent fuel connection (NG or a large LP tank).
  3. Who's doing the maintenance? If the answer is "nobody, it just needs to work when the power goes out," buy a unit with a self-test schedule and a service contract.

If you're still unsure, the safe default is Scenario A sizing for a home and Scenario B sizing for anything commercial. Undersizing is a bigger problem than oversizing — a 22kW unit running at 60% load lasts longer than a 20kW unit running at 95%.

I'm not a licensed electrician, so I can't speak to conductor sizing or load calculations. What I can tell you from a procurement and deployment perspective is that the fuel question is almost always the second question you should ask. The first is outage duration.

Honestly, I'm not sure why so many installers skip the surge protection conversation entirely. My best guess is it's not a line item they make margin on. But I've seen the aftermath of a lightning strike on an unprotected transfer switch, and the $200 protector would have saved a $2,400 repair. Not a hard decision. Total cost of ownership (i.e., fuel, maintenance, and installation — not just the unit price) matters more than the sticker.

I assumed for years that fuel type was the first decision. It's not. After a client lost a $12,000 catering contract because their portable propane unit ran dry during a 14-hour outage (nobody checked the tank level), we now quote every install with a fuel runtime calculation at 75% load. It adds five minutes to the quote and has saved at least two other clients from the same mistake.

That's the whole game in this corner of the electrical world: match the fuel, the kW, and the protection to the scenario in front of you. No universal answer. Anyone who tells you otherwise is selling something.

This entry was posted in Technical Blog. Bookmark the permalink.
author-avatar
Ingrid Bauer

Ingrid Bauer is an industrial automation and electromechanical systems analyst specializing in variable-frequency drives, motors, pumps, and complete power-drive systems. She applies IEC 61800-9-2 drive-efficiency methods, IEC 60034-30-1 motor efficiency classes, and ISO 9906 pump tests while examining torque-speed duty, harmonics, head, flow, and operating-point efficiency. She helps engineers size drive and pump combinations for real load profiles, cable lengths, ambient conditions, process control, energy use, and maintenance access.

Leave a Reply

Your email address will not be published. Required fields are marked *